« previous next »
Pages: [1] 2 3 |   Go Down

Author Topic: 8.25 Axle Prep/ Build  (Read 7779 times)

Offline calebsxj

  • Level 1
  • *
  • Posts: 94
8.25 Axle Prep/ Build
« on: 09/19/09 - 11:58PM »
Well i picked up the 8.25 rear axle today thanks to Austin "xj42". Its going to replace my Dana 35.

Been out in the elements so it needed some new paint!






Drained the Fluid


Took the carrier out, i plan to install 4.56s




With a wire brush and grinder i took it down to bare metal




After alot of grinding i primed the tubes


Once the pumpkin was cleaned down i primed it


I plan to coat the axle in black paint, once i put a 2nd coat of primer on.
Anybody recommend a good paint for this?
« Last Edit: 09/20/09 - 12:00AM by calebsxj »
Logged

Offline Jeeper guy

  • Level 3
  • ***
  • Posts: 332
  • OINK
Re: 8.25 Axle Prep/ Build
« Reply #1 on: 09/20/09 - 01:47AM »
Rustoleum safety yellow seems to stick the best for 8.25s for some reason... Must be something in the yellow?
Logged
First you crawl, then you walk, then you drive, then you crawl again....

Offline calebsxj

  • Level 1
  • *
  • Posts: 94
Re: 8.25 Axle Prep/ Build
« Reply #2 on: 09/20/09 - 01:59AM »
Yellow?  Haha i don't want an yellow axle, I was thinking black hammered...
Logged

Offline YJ_Aaron

  • Level 5
  • *****
  • Posts: 4255
  • Jeep @ Disney
Re: 8.25 Axle Prep/ Build
« Reply #3 on: 09/20/09 - 02:10AM »
Seems to be some pink covers rolling around lately!

Make sure you keep track of shims if you remove anything.  Will save you a life time when setting up the axle.
Logged
Is it possible for a jeep to ever truely be finished?<br /><br />Only the dead have seen the end of war---Plato

Offline calebsxj

  • Level 1
  • *
  • Posts: 94
Re: 8.25 Axle Prep/ Build
« Reply #4 on: 09/20/09 - 02:13AM »
Ok thats good info to know!  I have also been labeling everything i have been taking off.  I have not got to the ring and pinion yet.

Been looking at 4ws for Gears, what would you recommend Aaron?  Yukon or Superior?
Logged

Offline xj42

  • Level 3
  • ***
  • Posts: 293
Re: 8.25 Axle Prep/ Build
« Reply #5 on: 09/20/09 - 02:43AM »
Quote from: calebsxj on 09/20/09 - 01:59AM
Yellow?  Haha i don't want an yellow axle, I was thinking black hammered...

I use hammered black, brush on.  One quart has painted two axles and a variety of other items.  Cheaper than spray cans IMO.

Quote from: YJ_Aaron on 09/20/09 - 02:10AM
Seems to be some pink covers rolling around lately!

Make sure you keep track of shims if you remove anything.  Will save you a life time when setting up the axle.

Aren't there side adjuster on this axle?  I know the pinion still has shims for depth, and I thought preload was through a crush sleeve?  Correct?



Logged

Offline calebsxj

  • Level 1
  • *
  • Posts: 94
Re: 8.25 Axle Prep/ Build
« Reply #6 on: 09/20/09 - 02:45AM »
Ok ill look into the roll on paint, is it harder to apply around tight areas tho?

Quote from: xj42 on 09/20/09 - 02:43AM
I use hammered black, brush on.  One quart has painted two axles and a variety of other items.  Cheaper than spray cans IMO.

Aren't there side adjuster on this axle?  I know the pinion still has shims for depth, and I thought preload was through a crush sleeve?  Correct?




Logged

Offline xj42

  • Level 3
  • ***
  • Posts: 293
Re: 8.25 Axle Prep/ Build
« Reply #7 on: 09/20/09 - 03:19AM »
Quote from: calebsxj on 09/20/09 - 02:45AM
Ok ill look into the roll on paint, is it harder to apply around tight areas tho?


It can be, but it's not bad.
Logged

Offline calebsxj

  • Level 1
  • *
  • Posts: 94
Re: 8.25 Axle Prep/ Build
« Reply #8 on: 09/20/09 - 03:20AM »
ok kool ill look into that
Logged

Offline YJ_Aaron

  • Level 5
  • *****
  • Posts: 4255
  • Jeep @ Disney
Re: 8.25 Axle Prep/ Build
« Reply #9 on: 09/20/09 - 04:57PM »
Honestly Yukon or Superior are both good gears.  There are several companies out there to avoid but neither of those is on that list. 

I have done an 8.25 so can't swear how you set pinion preload. 
Logged
Is it possible for a jeep to ever truely be finished?<br /><br />Only the dead have seen the end of war---Plato

Offline calebsxj

  • Level 1
  • *
  • Posts: 94
Re: 8.25 Axle Prep/ Build
« Reply #10 on: 09/20/09 - 11:05PM »
Ok I was leaning towards superior gears. They are cheaper then Yukon, just want something that will last and are quite.
Logged

Offline YJ_Aaron

  • Level 5
  • *****
  • Posts: 4255
  • Jeep @ Disney
Re: 8.25 Axle Prep/ Build
« Reply #11 on: 09/21/09 - 12:08AM »
They are about the same to be honest in my opinion.  Either setup right will last a long time and be quiet.
Logged
Is it possible for a jeep to ever truely be finished?<br /><br />Only the dead have seen the end of war---Plato

Offline LoneWolf

  • Level 5
  • *****
  • Posts: 2557
Re: 8.25 Axle Prep/ Build
« Reply #12 on: 09/21/09 - 12:18AM »
Looks good Caleb. You might check into implement paint at one of the farm stores. It's thicker and will cover many imperfections.
Logged
EVERY NORMAL MAN MUST BE TEMPTED AT TIMES TO SPIT ON HIS HANDS, HOIST THE BLACK FLAG, AND BEGIN SLITTING THROATS.

Offline xj42

  • Level 3
  • ***
  • Posts: 293
Re: 8.25 Axle Prep/ Build
« Reply #13 on: 09/21/09 - 12:36AM »
Quote from: LoneWolf on 09/21/09 - 12:18AM
Looks good Caleb. You might check into implement paint at one of the farm stores. It's thicker and will cover many imperfections.

Imperfections?  That thing was pristine when it changed hands.
Logged

Offline LibertyPatriot

  • I vote for BACON!
  • Charter Members
  • Level 5
  • *
  • Posts: 1766
  • Web Wheeler!
Re: 8.25 Axle Prep/ Build
« Reply #14 on: 09/21/09 - 12:38PM »
Are you going to show it or wheel it?  Dang, just slap some black paint on there and go.  Gonna get scratched up anyway...
Logged
I'd put something funny here, but you probably wouldn't get it anyway...
Pages: [1] 2 3 |   Go Up
« previous next »